如果自上料水泥搅拌车有刮花情况，需要及时进行处理，以保证搅拌车的正常使用和延长其寿命。以下是一些常见的刮花磨损现象以及处理方法：

If there are scratches on the self feeding cement mixer truck, timely treatment is necessary to ensure the normal use of the mixer truck and extend its lifespan. The following are some common scratches and wear phenomena and treatment methods:

1、搅拌车小伤痕的修补：

1. Repair of small scratches on the mixer truck:

搅拌车身如果发现伤痕，先检查伤痕的程度。如果只是很浅的刮伤表漆，立即用混合剂处理，擦拭方法为直线擦拭。伤痕消失后，用更细的混合剂擦拭之后再打上蜡。

If any scars are found when stirring the car body, first check the extent of the scars. If it is only a shallow scratch on the surface paint, immediately treat it with a mixture and wipe it in a straight line. After the scars disappear, wipe with a finer mixture before applying wax.

2、搅拌车擦伤的修补：

2. Repair of scratches on the mixing truck:

所有的搅拌车在使用过程中都有擦伤，修补方法是伤痕部分填上与车身相同的镀膜剂。镀膜剂可涂一次、二次、三次，次数越多，会涂得越干净。但整个搅拌车身的均匀处理也很重要。

All mixing trucks have scratches during use, and the repair method is to fill the damaged parts with the same coating agent as the vehicle body. The coating agent can be applied once, twice, or three times, and the more times it is applied, the cleaner it will be applied. But the uniform treatment of the entire mixing body is also important.

3、搅拌车表漆剥落的修补：

3. Repair of paint peeling on the mixer truck surface:

较深的伤痕，是观察金属面是否露出，如果看不到金属面就不会生锈，可以专心地涂上修饰漆。用笔尖一点一点地点上去，然后等漆完全干。

For deeper scars, the key is to observe whether the metal surface is exposed. If the metal surface is not visible, it will not rust. You can focus on applying decorative paint. Use the tip of the pen to apply it bit by bit, and then wait for the paint to completely dry.

4、搅拌车较深伤痕的修补：

4. Repair of deep scars on the mixer truck:

很深但细长的伤痕，用彩色油灰可以修补得很好。伤痕处用砂纸，不要随便将伤痕面扩大，重要的是将脏污干净。油灰要仔细地涂抹，使之完全进入内部。涂上混合剂、上蜡，结束工作。

Deep but slender scars can be repaired well with colored putty. Use sandpaper at the scar area, do not randomly enlarge the scar surface, it is important to clean the dirt. The putty should be carefully applied so that it fully enters the interior. Apply the mixture, wax, and finish the work.

5、搅拌车凹陷的修补：

5. Repair of dents in the mixer truck:

凹陷处理是车身保养中麻烦的工作之一，重要的是打好底子，若这个步骤做不好，涂装做得再好效果都不佳。喷漆时，不要忘记用报纸遮好四周，使涂料不要向周围扩散。

Depression treatment is one of the troublesome tasks in vehicle maintenance, and the important thing is to lay a solid foundation. If this step is not done well, no matter how well the coating is done, the effect will not be good. When painting, do not forget to cover the surroundings with newspapers to prevent the paint from spreading around.

6、搅拌车的防锈：

6. Rust prevention of mixing trucks:

发现车体生锈后，立即着手，如果放任不管，锈点就会慢慢扩大。防止生锈的方法是用砂纸擦净，或用使锈点变化的化学合成剂。

After discovering rust on the car body, immediately start solving it. If left unchecked, the rust spots will gradually expand. The method to prevent rust is to clean it with sandpaper or use a chemical synthetic agent that changes the rust spots.

7、搅拌车漏水对策：

7. Countermeasures for water leakage in the mixing truck:

车门、行李箱周围粘贴的防水条容易剥落、扭曲。但如果没有破裂、变形，可以再一次使用，只需将它重新粘贴，就可以防止漏水。用保护剂恢复橡胶本身的弹力也很重要。

The waterproof strips pasted around the car doors and luggage compartments are prone to peeling and twisting. But if it is not cracked or deformed, it can be used again, just by re pasting it to prevent water leakage. It is also important to restore the elasticity of the rubber itself with protective agents.

8、搅拌车机油保养窍门：

8. Tips for maintaining mixer truck oil:

机油量过多过少都会影响引擎，理想的量是紧靠油量刻度上限的部位。补充用机油，尽量准备与使用中的机油相同等级的产品。注意不要溅到引擎周围，一个月检测一次。

Too much or too little oil can affect the engine, and the ideal amount is close to the upper limit of the oil level scale. Replenish oil and try to prepare products of the same grade as the oil in use. Be careful not to splash around the engine, check once a month.

9、搅拌车保险杠伤痕的修补：

9. Repair of Bumper Scars on Mixing Truck:

保险扛的伤痕处理方法是将毛刺削去，坑洼部分涂上油灰使之平滑。专用油灰，准备各种颜色，选择接近的颜色。与车身同色的保险杠，喷漆很重要。

The treatment method for the scars on the safety shoulder is to remove the burrs and apply putty to the potholes to make them smooth. Special putty, prepare various colors, and choose similar colors. Painting the bumper in the same color as the body is important.

1. 研磨法：使用砂纸或砂轮将刮花处进行研磨，直平整。

1. Grinding method: Use sandpaper or grinding wheel to grind the scratched area until it is flat.

2. 填补法：使用填补材料将刮花处填补平整，等填补材料干透后再进行打磨。

2. Filling method: Use filling material to fill the scraped area flat, and wait for the filling material to dry thoroughly before polishing.

3. 磨灰法：如果刮花较浅，可以用灰针磨灰使刮花处的灰面匀整，再用布擦拭干净。

3. Grinding method: If the scraping is shallow, a dust needle can be used to grind the dust surface at the scraping point to make it even, and then a cloth can be used to wipe it clean.

4. 漆面喷涂法：对于严重的刮花，可以将刮花处的油漆研磨掉，再进行漆面喷涂，使搅拌车表面恢复平整。需要注意的是，对于涂料颜色需要与原来的颜色相同，否则会影响搅拌车的美观度。

4. Paint spraying method: For severe scratches, the paint at the scratches can be ground off and then sprayed to restore a smooth surface of the mixer truck. It should be noted that the paint color should be the same as the original color, otherwise it will affect the aesthetics of the mixing truck.

同时，在进行处理时寻求的维修人员进行处理，保证处理效果和性。更多相关事项就来我们网站http://www.sdzkjf.cn咨询吧！

At the same time, seek professional maintenance personnel for handling to ensure the effectiveness and safety of the treatment. For more related matters, come to our website http://www.sdzkjf.cn Consult!