水泥自上料搅拌车由于功能性能优越，因此应用范围越来越广泛，但是在使用期间也会出现各种问题，所以需要提前进行了解到，比如说水泥自上料搅拌车装载问题，这要怎么操作？

　　Cement self-feeding mixer is more and more widely used because of its superior function and performance, but there will be various problems during the use, so it is necessary to understand in advance, such as the loading problem of cement self-feeding mixer, how to operate this?

　　水泥自上料搅拌车装载时连接紧急驱动软管，依靠其它搅拌车的动力。驱动拌筒旋转并将混凝土排出。但是若减速器同时发生故障时，则不可采用此法。准备好一根紧急驱动软管，卸下接管和接头盖；将故障水泥自上料搅拌车的发动机熄火；将紧固螺母朝左旋松；再将旋钮朝右旋转，直到不能再旋为止；将高压软管从马达接头处卸下；

　　When the cement is loaded from the loading mixer, connect the emergency drive hose and rely on the power of other mixer trucks. Drive the drum to rotate and discharge the concrete. However, if the reducer fails at the same time, this method cannot be used. Prepare an emergency drive hose, remove the nozzle and joint cover; The engine of the mixing car of the faulty cement is flameout. Unscrew the fastening nut to the left; Turn the knob to the right until it can no longer turn; Unload the high pressure hose from the motor joint;

　　将操作手柄于空档位置；将发动机熄火；将高压软管从高压油管处卸下；将紧急驱动软管接到高压油管上；用紧急驱动软管上的接头盖将驱动车的高压软管盖起，以防漏油。启动水泥自上料搅拌车的发动机。将水泥自上料搅拌车的操作手柄拨“出料”位置，使故障车内的混凝土排出。紧急驱动完毕后，使两车各自恢复原状。

　　The operating handle to the neutral position; Turn off the engine; Unload the high-pressure hose from the high-pressure tubing; Connect the emergency drive hose to the high-pressure tubing; Cover the high pressure hose of the drive truck with the connector cover on the emergency drive hose to prevent oil leakage. Start the engine of the cement self-feeding mixer. Move the cement from the operation handle of the mixing truck to the "discharging" position, so that the concrete in the car with failure is discharged. After the emergency drive, restore the two cars to their original shape.

　　为了提高水泥自上料搅拌车的工作效率，以上装载等问题就需要多了解诶，此外还要知道一个问题--堵料，这也是常见的问题，原因之一便是水泥自上料搅拌车因料仓内无法加装料位机，所以基本都有时间控制。

　　In order to improve the working efficiency of cement self-feeding mixer, the above loading and other problems need to be understood. In addition, we also need to know a problem -- material blocking, which is also a common problem. One of the reasons is that the cement self-feeding mixer cannot be equipped with a material level machine in the bin, so it basically has time control.

　　如何设置时间参数，上下料时间设置还是比较简单的，在初次使用时，先设置一个比较短的时间，然后根据每次吸料位置慢慢加，当达到料位达到吸料口的时间，再减去一秒就是合理时间。放料时间是确保放完料再加一秒。

　　How to set the time parameters, the loading and unloading time setting is relatively simple, in the first use, set a relatively short time, and then according to each suction position slowly add, when the material level to reach the suction mouth time, then minus a second is a reasonable time. Discharging time is to ensure the discharging of the material plus one second.

　　正确的方式是物料在吸料口和空气形成一定的气物混合比，在气流推动下均匀流入上料机。这个时候我们需要将料仓设计带有补气功能。如果物料积压时间过长可能会很硬，这个时候需要在料仓上装一个振荡器，敲碎结块的物料。

　　The correct way is that the material in the suction port and air to form a certain air mixture ratio, under the impetus of air flow into the feeding machine. At this time we need to design the bin with qi function. If the material backlog time is too long, it may be very hard. At this time, an oscillator needs to be installed in the bin to break the lumped material.

　　水泥自上料搅拌车装载问题的具体操作以及其他问题的了解就到这里了，如果您还想知道更多问题，就来我们网站www.sdzkjf.cn咨询客服人员吧。

　　The concrete operation of the loading problem of the cement mixing truck and the understanding of other problems are here. If you still want to know more problems, come to our website www.sdzkjf.cn to consult customer service staff.