1.清洁机器时,只能擦拭电箱,不能冲洗。
1. When cleaning the machine, only wipe the electric box, not wash it.
2.调整主轴密封圈,拆下泵芯和进给支架,然后拧紧三个螺钉。螺钉拧紧后的标准:8英寸可动手可轻松拉动主轴螺钉。
2. Adjust the main shaft seal ring, remove the pump core and feed bracket, and then tighten the three screws. Standard after screw tightening: 8-inch can easily pull spindle screw by hand.
3.在施工现场移动机器时,不管间隔如何,都有必要拔掉电源线。
3. When moving the machine on the construction site, it is necessary to unplug the power line regardless of the interval.
4.机器作业时,有必要关闭并锁上电箱门,以避免灰尘和湿气侵入并损坏机器部件。
4. When the machine is working, it is necessary to close and lock the electric box door to avoid dust and moisture invasion and damage to machine parts.
5.在作业之前和之后,有必要给轴承箱加油,并经常查看变速箱油。
5. Before and after operation, it is necessary to oil the bearing box and check the gearbox oil frequently.
6.每次清洁泵芯时,有必要加少数硅油光滑和防刺绣。目的是维护转动铁芯免于生锈,并在下次运用后顺畅启动。
6. When cleaning the pump core, it is necessary to add a small amount of silicone oil for smoothness and anti embroidery. The purpose is to protect the rotating core from rusting and to start smoothly after the next operation.
自上料搅拌车选用全液压技术,因而要考虑所有液压技术是否,以及液压视觉质量。因为动力来自发动机,除了考虑发动机的功能和质量外,还有必要考虑底盘的功能,承载能力和质量。在维护车辆设备的过程中,有必要严格依照正确的操作过程进行,以坚持作用。
Since the full hydraulic technology is selected for the self feeding mixer, it is necessary to consider whether all the hydraulic technology is advanced or not, and the visual quality of the hydraulic system. Because the power comes from the engine, in addition to considering the function and quality of the engine, it is also necessary to consider the function, bearing capacity and quality of the chassis. In the process of maintenance of vehicle equipment, it is necessary to strictly follow the correct operation process to adhere to the role.
经过自上料搅拌车清洁内部混凝土的办法
Method of cleaning internal concrete by self loading mixer
在咱们的日子中,自上料搅拌车是一种运送混凝土的特殊车辆。通常在车辆后边装置一个大型水箱来搅拌混凝土。可是,因为咱们需要在长期运用期间清洁车内的混凝土,咱们将在下面介绍具体的清洁办法。
In our days, self loading mixer is a special vehicle for transporting concrete. A large water tank is usually installed behind the vehicle to mix concrete. However, since we need to clean the concrete inside the vehicle during long-term use, we will introduce the specific cleaning methods below.
1.准备应急驱动软管,关闭混凝土主动搅拌车,然后拆下液压马达上的高压油管接头。
1. Prepare the emergency drive hose, close the active concrete mixer, and then remove the high-pressure oil pipe joint on the hydraulic motor.
2.拆下高压油管,并将其与毛病车上相应连接器的应急驱动软管连接。
2. Remove the high-pressure oil pipe and connect it with the emergency drive hose of the corresponding connector on the defective vehicle.
3.发动机搅拌车,其操控手柄设置在卸料方位,以排除车内混凝土
3. The control handle of the engine mixer is set at the unloading position to remove the concrete in the truck
4.紧急驱动完成后,拆下驱动软管并恢复车辆的原始状态。
4. After the emergency drive is completed, remove the drive hose and restore the original state of the vehicle.
Thank you for reading. This article is from Zhongke Jufeng mixer. For more information and questions, please click: http://www.sdzkjf.cn We will continue to work hard to provide services for you, thank you for your support!
上一篇:水泥自动搅拌车有哪些注意事项?
下一篇:自上料搅拌车机油怎么使用是正确的?