自动搅拌车存在抱轴及闷机跳闸现象的原因必要及时找到，不然故障一旦不及时，随着时间越拖越久，就会导致问题的严重性越来越大，下面小编为您解答。

It is necessary to find out the cause of the axle holding and the machine blocking tripping of the automatic mixer in time, otherwise, if the fault is not solved in time, it will lead to the problem becoming more and more serious as time goes on. Here are some answers for you.

自动搅拌车存在抱轴现象原因：

Reasons for axle holding of automatic mixer:

1.可能是拌和主机进水管与冲水方位原因。冲水点方位和冲刷方向不正确的话，也或者是冲水压力过低，导致水在进入主机内部后，不能将暂时粘结在轴上的混凝土冲刷掉，则时刻久了就简单构成抱轴。

1. It may be caused by the water inlet pipe and flushing position of the mixing machine. If the direction of flushing point and flushing direction are incorrect, or the flushing pressure is too low, so that the concrete temporarily bonded to the shaft cannot be washed away after the water enters the main engine, then the shaft holding will be simply formed after a long time.

2.可能是质料投料方位问题。拌和混凝土所用的物料主要是砂石骨料、水泥、粉煤灰、水和外加剂等。质料水泥若包裹砂石遇水结块，假如拌和不充沛就简单粘在拌和轴上，若水泥进料口方位方向不合理，使拌和轴不能快速充沛拌和，就简单构成抱轴现象。

2. It may be the material feeding direction. The materials used for mixing concrete are mainly sand aggregate, cement, fly ash, water and additives. If the material cement is wrapped with sand and gravel and agglomerates when encountering water, it will simply stick to the mixing shaft if the mixing is not sufficient. If the direction of the cement feed inlet is unreasonable, so that the mixing shaft can not be quickly and sufficiently mixed, it will simply form the phenomenon of shaft holding.

3.在结束作业之后没有及时对拌和机内部进行清洗，或清洗不干净，导致拌和轴外表仍有残留的混凝土，枯燥后凝固在拌和轴上，假如长期如此则十分简单发生抱轴现象。

3. After the completion of the operation, the internal part of the mixer is not cleaned in time, or the cleaning is not clean, resulting in the residual concrete on the surface of the mixing shaft, which solidifies on the mixing shaft after being dry. If this is the case for a long time, the phenomenon of holding the shaft is very simple.

自动搅拌车闷机跳闸原因：

Reasons for the trip of the automatic mixer:

1.投料过多，引起拌和机负荷过大。

1. Excessive feeding causes excessive load of the mixer.

2.三角传动皮带太松，使传动体系功率低。

2. The triangular transmission belt is too loose, resulting in low power of the transmission system.

3.拌和主机上盖检修开关被振松，引起停机。

3. The safety maintenance switch on the upper cover of the mixing host is loosened, causing the shutdown.

4.拌和体系叶片与衬板之间的空隙过大，拌和过程中，增大了阻力。

4. The gap between the blade and the lining plate of the mixing system is too large, which increases the resistance during the mixing process.

自动搅拌车存在抱轴及闷机跳闸现象的原因就找到了，注意在平常使用中的每日检查以及定期维护，更多相关事项就来我们网站http://www.sdzkjf.cn咨询吧！

The reason for the phenomenon of axle holding and machine blocking tripping of the automatic mixer has been found. Pay attention to the daily inspection and regular maintenance in normal use. More relevant matters can be found on our website http://www.sdzkjf.cn Consult!