在设备实际操作运行过程中，自动搅拌车的变速器是一个非常重要的部件。因此，我们在使用过程中对其油质需要有一定的检测工作，那么我们具体应该怎么进行操作呢？

In the actual operation of the equipment, the transmission of the automatic mixer is a very important component. Therefore, we need to have a certain detection of its oil quality in the process of use, so how should we operate?

1、将自动搅拌车停放在水平地面上，并拉紧手制动。

1. Park the automatic mixer on a level ground and tighten the hand brake.

2、让发动机怠速运转数分钟。

2. Allow the engine to idle for several minutes.

3、踩住制动踏板，将操纵手柄拨倒挡、前进挡等位置，并在每个挡位上停留几秒钟，使液力变矩器和所有换挡执行元件中都充满液压油。将操纵手柄拨停车挡位置。

3. Step on the brake pedal, turn the joystick to the reverse gear, forward gear and other positions, and stay in each gear for a few seconds, so that the hydraulic torque converter and all shift actuators are filled with hydraulic oil. Turn the joystick to the parking position.

4、从加油管内拨出自动变速器油尺，将擦干净的油尺全部插入加油管再拔出，检查油尺上的油面高度。

4. Pull out the automatic transmission dipstick from the filler pipe, insert all the cleaned dipsticks into the filler pipe and then pull them out, and check the oil level on the dipstick.

5、搅拌车发动机很热时，切勿开启散热器盖。不然很有可能会造成 迸溅的冷却液或热蒸气焚烧。搅拌车发动机制冷后，保证冷却液液面在满和低中间。要是没有，您须要加上蒸溜水或矿泉水或冷却液。

5. Do not open the radiator cap when the mixer engine is very hot. Otherwise, it is likely to cause splashed coolant or hot steam to burn. After the mixer engine is cooled, ensure that the coolant level is between full and low. If not, you need to add distilled water or mineral water or coolant.

兑水后液体的相对高度不可超出满水量。假如发觉冷却液在短期内快速降低，则自上料式混凝土搅拌车检查数据应查验制冷系统是不是外泄或查验服务点。

The relative height of the liquid after mixing with water shall not exceed the full water volume. If it is found that the coolant decreases rapidly in a short time, the inspection data of the self loading concrete mixer should check whether the refrigeration system leaks or check the service point.

在对自动搅拌车变速器进行检查或故障诊断前，要对变速器油面和油质进行检查。把选挡手柄放在P位，将发动机在怠速时少运转数分钟，油液达到正常工作温度，搅拌车须停放在水平路面上，这样才能确保在差速器和变速器之间的油面高度正常、稳定。

Before the inspection or fault diagnosis of the automatic mixer transmission, the oil level and quality of the transmission should be checked first. Put the gear selector handle in position P, run the engine at idle speed for at least a few minutes, the oil reaches the normal working temperature, and the mixer must be parked on a horizontal road, so as to ensure that the oil level between the differential and the transmission is normal and stable.

自动搅拌车变速器油质的检测方式便是以上内容了，希望能够给您好的帮助吧，更多关于搅拌车使用的事项就来关注我们网站http://www.sdzkjf.cn吧！

The oil quality detection method of automatic mixer transmission is the above content. I hope I can help you. For more information about the use of mixer, please pay attention to our website http://www.sdzkjf.cn Come on!