正所谓量体裁衣,对水泥搅拌车的衣服就是车框架。如果衣服裁的不合理,对于车不仅仅就是不好看那么简单了,它的安全性也就大大下降。轮距和车框架的搭配也是非常重要的。因为上面我们就说车框架是在轮胎之上的。那么合理的轮距承载多大的车框架,必须在合理承受范围之内。
It is the so-called tailor-made clothes. The clothes of the cement mixer are the car frame. If the clothes are cut unreasonably, the car is not only ugly, but also its safety will be greatly reduced. The matching of track width and car frame is also very important. Because we said above that the car frame is on the tire. Then the reasonable wheel base bearing the vehicle frame must be within the reasonable bearing range.
从而我们也知道,一个搅拌车的环境适应能力,不仅仅受到发动机的影响,还受到轮距的影响,那么我们自然而然知道小型搅拌车轮距的选择有就非常重要了。我们都知道车的框架是在轮胎之上的,而正因此与地面接触的就是轮胎。那么也就是说判断一个道路是否能过,主要就是看自己的轮距是否在这个道路宽度之内。
Therefore, we also know that the adaptability of a mixer truck to the environment is not only affected by the engine, but also by the track width, so we naturally know that the choice of track width of small mixer truck is very important. We all know that the frame of the car is on the tire, and therefore it is the tire that contacts the ground. That is to say, to judge whether a road can be crossed, we mainly depend on whether our wheel base is within the width of the road.
此外搅拌车的机械密封组装和拆卸应该在非常干净的环境中进行,使用的润滑油也应该高质量且纯净的,在进行全方面清洁保养中时,我们要如何做呢?应该先将机械密封区域的各个部位清洗干净。接着再将两端密封静环装置均匀且平稳的压倒定位孔当中,要注意保护好静环密封面,不能造成密封面磨伤或损坏,还有要利用导向套将多功能搅拌机的动环正确的安装到轴上,在合上油室端盖。
In addition, the mechanical seal assembly and disassembly of the mixer truck should be carried out in a very clean environment, and the lubricating oil used should also be high-quality and pure. What should we do in all aspects of cleaning and maintenance? All parts of the mechanical seal area should be cleaned first. Then press the sealing static ring device at both ends evenly and stably into the positioning hole. Pay attention to protect the sealing surface of the static ring, so as not to cause abrasion or damage to the sealing surface. In addition, use the guide sleeve to correctly install the moving ring of the multi-function mixer on the shaft, and close the end cover of the oil chamber.
这期间要注意不能碰撞到机械的密封面,如果要对搅拌机进行机械密封的拆卸,可以按照上面的顺序反复进行,如果要更换多功能搅拌机的润滑脂。
During this period, pay attention not to collide with the mechanical sealing surface. If you want to disassemble the mechanical seal of the mixer, you can repeat the above sequence. If you want to replace the lubricating grease of the multi-function mixer.
搅拌车的润滑油的黏度过低,其润滑效果也会随之降低,部件也会产生摩擦力,随之使其温度升高,尤其是夏季会格外偏高,具体要增加了搅拌车零部件运行时的摩擦力,减速器运行时要克服摩擦力做功,也将产生很大一部分热量,使减速器温度升高。夏季的高温是造成搅拌机减速器温度上升的外部因素。夏季本身气温过高,混凝土搅拌站特殊的工作环境必然会造成设备的温度过高。
If the viscosity of the lubricating oil of the mixer truck is too low, its lubrication effect will be reduced, and the components will also produce friction, which will increase its temperature, especially in summer. Specifically, the friction of the parts of the mixer truck will be increased. When the reducer is running, it will overcome the friction to do work, which will also produce a large part of heat, which will increase the temperature of the reducer. The high temperature in summer is the external factor causing the temperature rise of mixer reducer. The temperature in summer is too high, and the special working environment of the concrete mixing plant will inevitably cause the temperature of the equipment to be too high.
自上料水泥搅拌车在生产过程中如果润滑油的黏度过高,这时候搅拌车轴承负荷增大,摩擦加剧,产生大量热量,油的黏度过高,流动性差,导致运行负荷增大,将产生很大一部分热量,使减速器温度升高。
If the viscosity of the lubricating oil of the self loading cement mixer is too high in the production process, the bearing load of the mixer increases, the friction intensifies, and a lot of heat is generated. The viscosity of the oil is too high and the fluidity is poor, resulting in the increase of the operating load, which will generate a large part of heat and raise the temperature of the reducer.
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website http://www.sdzkjf.cn And consult our staff, will serve you wholeheartedly.
上一篇:搅拌车不要过度热车及熄火后使用电器设备
下一篇:自上料水泥搅拌车的动力系统分析